Think of sensitivity as a speed (de)amplifier. When to use? When you want your out of game speed to set the bar for your in game sensitivity. Whatever the value, Half-Life will use it as guidance. Noforcemspd forces Half-life to use whatever speed settings you have applied to your desktop via mouse properties. Noforcemspd – uses desktop mouse speed settings. A part from troubleshooting this command has no practical use, despite popular belief. When to use? When you are experiencing difficulty with button assignments. There is really no benefit to this command, and in actuality it is quite buggy at times. What does that mean? Usually when you start up Half-Life (or in this case Counter-Strike) your mouse configuration will switch to application mode, allowing the assignment of keys already assigned to your desktop (like mouse3). Noforcemparms – reverts to desktop mouse button settings. When to use? When mouse acceleration is disabled on your desktop and you want the same results for your in game experience. The noforcemaccel command will make sure Half-Life does not try and manage mouse accel when it is disabled in your windows options. For the most part (when it comes to gaming and precision accuracy) mouse acceleration is a fickle feature. Noforcemaccel – reverts to desktop mouse acceleration settings. Luckily, they have a direct correlation to your mouse so you get to learn all about them right now. The following three commands are the most used commands you will find in a users launch options. Right click the steam icon on your taskbar -> Play Games -> Right click Counter-Strike -> Properties -> Launch Options. With this ratio your mouse speed will be cut in half (0.5), changing it to a sensitivity of 2 while zooming. What does that mean? Let us say you have an in-game sensitivity of 4, and a zoom_sensitivity_ratio of 0.5. Zoom_sensitivity_ratio – Temporarily adjusts the sensitivity of your crosshair upon zooming dependent on the ratio set. Sensitivity – The console equivalent of “Mouse sensitivity.” This is the most effective method for changing sensitivity as not only can you include decimal values, but you can also adjust it faster on the fly. M_yaw – Adjusts the sensitivity of turning left and right with the mouse. M_side – Adjusts the sensitivity of sideways mouse movement. M_pitch – Adjusts the sensitivity of up and down mouse movements. M_forward – Adjusts the sensitivity of forward and backwards mouse movement. M_filter – This would be the console equivalent of the Mouse Filter command. These commands can be adjusted before or during game via the developer’s console ( key). Check out GotGear if you are looking for a new mouse or mousepad. While a sensitivity of 5 or below is recommended and generally accepted, your choice is totally dependant on your current mouse and surface selection. Mouse sensitivity: This option allows you to change your in-game sensitivity, which sets how fast your crosshair moves. This also will hurt you in the long run, not only will your aim cease to improve but those already skilled will find this option to be unhelpful as it throws your aim off. Auto-Aim is disabled on most servers as many believe it to be a very cheap feature. Joystick look: Joystick look is the same concept as Mouse look, except this time for the joystick.Īuto-Aim: Aims at enemies automatically. This is because your game does not attempt to detect and initialize a joystick at startup. Disabling Joystick and all it’s byproducts can in fact decrease load times slightly, which will be more noticeable on a slower system. Joystick: Enable this if you prefer to use a joystick over a mouse. Theoretically, with mouse filter off, you could also receive a slight FPS boost on lower end systems. This means using older data to move your mouse instead of the most up to date information. If turned on, Counter-Strike will calculate all your mouse movements over the last two frames to find an average and attempt to give you a more fluid feel. Enabling it will only distort your aim, moving your crosshair slightly off cue from where you want it. This may sound like a good idea, but it is best left unchecked. Mouse Filter: Mouse filter smoothes out mouse movement. Mouse look: Mouse look should be checked if you are using a mouse, allowing you to “look” with the mouse. Up will become down and down will become up. Reverse Mouse: Ticking this option will invert your mouse’s up-down axis. Many of the options are self explanatory, but let us go over them a little just to be clear. From there, select the “Mouse” tab from the menu. After starting up Counter-Strike, go into Options.
0 Comments
Leave a Reply. |